Pelco ICS210 Bedienungsanleitung

INSTALLATIONICS210 Series Camclosure®Integrated Camera SystemC2491M-D (8/06)

10 C2491M-D (8/06)REINSTALL CAMERA MODULEReinstall the camera module. Refer to Figure 9. Make sure the top of the camera is oriented properly. On the

C2491M-D (8/06) 11REPLACE COVERPlace the cover of the ICS210 onto the base of the unit. Using the screwdriver bit (supplied), tighten the three tamper

12 C2491M-D (8/06)Adjustments (Color Camera Only) If you have a color camera, it is set up at the factory and normally requires no adjustments. Someti

C2491M-D (8/06) 13AUTO IRIS LEVEL ADJUSTMENT If you have a varifocal lens or fixed focal length lens with an auto iris, you can adjust the iris level s

14 C2491M-D (8/06)HEATER BOARD REMOVALTo remove the heater board, do the following:1. Disconnect the four-pin heater connector (red, orange, and black

C2491M-D (8/06) 15SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS Refer to Figure 15. The switch is located next to the lens. Automatic b

16 C2491M-D (8/06)SWITCH SETTINGS FOR VARIFOCAL LENSThe high resolution camera with varifocal lens and auto iris is configured at the factory for autom

C2491M-D (8/06) 17Specifications General Pan/Tilt Adjustment Manual; 5° above horizontal to 20° below horizontal tilt; 24° pan adjustment when using t

18 C2491M-D (8/06)REVISION HISTORYManual # Date CommentsC2491M 6/05 Orginal version.C2491M-A 7/05 Revised per new camera shell design for varifoca

PRODUCT WARRANTY AND RETURN INFORMATIONWARRANTYPelco will repair or replace, without charge, any merchandise proved defective in material or workmansh

2 C2491M-D (8/06) Contents Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Worldwide Headquarters3500 Pelco WayClovis, California 93612 USAUSA & CanadaTel: 800/289-9100Fax: 800/289-9150InternationalTel: 1-559/292-1981Fax:

C2491M-D (8/06) 3 Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) t

4 C2491M-D (8/06) Description The ICS210 Series Camclosure ® is a wedge style integrated camera system that is quick and easy to install. The syste

C2491M-D (8/06) 5 Installation PREPARE MOUNTING SURFACE 1. Remove the cover of the ICS210. Use the screwdriver bit that is provided to loosen the th

6 C2491M-D (8/06) 4. Select a fi xed or adjustable mounting pattern (refer to Figure 3 and Figure 4 ). Using the mounting plate as a template,

C2491M-D (8/06) 7 INSTALL BASE WITHOUT CONDUIT 1. Pull the power and video wiring for the camera through the mounting surface and then through the w

8 C2491M-D (8/06) 3. Using a blunt tool push out the wiring plug in the bottom of the base (refer to Figure 6). Pull the wiring inside the base.Fig

C2491M-D (8/06) 95. Pull wiring through the conduit opening (refer to Figure 8):a. Use a 1/16” hex head wrench to loosen the hex head inset screw.b. U