INSTALLATIONC3422M-B (3/08)PressurizedSpectra® IV SeriesPendant Back Boxwith Fiber Optic Option
10 C3422M-B (3/08).NOTES:• Input power for the dome is 24 VAC only. Power consumption is 73 VA per dome. • Use a 24 VAC transformer with a minimum of
C3422M-B (3/08) 11Table E. Configuration of Wire HarnessPin Wire Color Function9-Conductor CableABlack Alarm 1BRed Alarm 2C White Alarm 3DGreen Alarm
12 C3422M-B (3/08)Switch SettingsWARNING: If you are using Pelco D or Pelco P protocol control, your system may not operate if the baud rate and addre
C3422M-B (3/08) 13Table G. Switch Settings for SW1, Pelco P Protocol ControlNOTE: For Coaxitron controls, SW1 is not used; set all switches to the
14 C3422M-B (3/08)SPECTRAADDRESSSWITCH SETTINGSW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-871 ON ON ON OFF OFF OFF ON OFF72 OFF OFF OFF ON OFF OFF O
C3422M-B (3/08) 15SPECTRAADDRESSSWITCH SETTINGSW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8151 ON ON ON OFF ON OFF OFF ON152 OFF OFF OFF ON ON OFF O
16 C3422M-B (3/08)SPECTRAADDRESSSWITCH SETTINGSW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8223 ON ON ON ON ON OFF ON ON224 OFF OFF OFF OFF OFF ON ON
C3422M-B (3/08) 17SpecificationsGENERALConstructionBack Box 316L stainless steelDome Drive Aluminum, thermoplasticLower Dome Trim Ring 316L stainles
18 C3422M-B (3/08)Input Power24 VAC 73 VA nominal (with heater)24 VDC 3 A nominal (with heater)Fuse 1.25 AAuxiliary Outputs 2Alarm Inputs 75.9 (15.1)1
PRODUCT WARRANTY AND RETURN INFORMATIONWARRANTYPelco will repair or replace, without charge, any merchandise proved defectivein material or workmanshi
2 C3422M-B (3/08)PreinstallationNOTE: This manual is designed to be a reference tool for the installation of your system. For best results and ease of
Worldwide Headquarters3500 Pelco WayClovis, California 93612 USAUSA & CanadaTel: 800/289-9100Fax: 800/289-9150InternationalTel: 1-559/292-1981Fax:
C3422M-B (3/08) 33. Loosen the V-band attached to the back box and let it hang to the side.Figure 3. Loosening the V-band4. Prepare the lower dome fo
4 C3422M-B (3/08)Figure 5. Attaching the Back Box Leash6. Install the dome drive. Refer to Table A for a list of compatible dome drives and back boxe
C3422M-B (3/08) 57. Install the lower dome:a. Position the lower dome so that the blower duct inside the back box is between the studs attached to the
6 C3422M-B (3/08)d. Refer to the Operation/Programming manual (C3412M) for instructions on how to view the current readings for temperature and pressu
C3422M-B (3/08) 7Site Installation1. Feed a fiber optic cable (not supplied) and the supplied wiring harness into the front of the mount and out the b
8 C3422M-B (3/08)Figure 10. Removing the Back Box Mounting Plate3. Thread the wiring from the mount through the mounting plate, and then attach the m
C3422M-B (3/08) 9Figure 12. Attaching the Wire Harness Connector
Kommentare zu diesen Handbüchern