Pelco IP3701H-2 Bedienungsanleitung

INSTALLATIONC2941M-C (6/08)IP3701H-2 Series IP Color Camera

10 C2941M-C (6/08)InstallationLENS MOUNTINGThe camera can be used with a fixed iris, manual iris, or auto iris lens. The camera is factory set for a

C2941M-C (6/08) 11Wiring TablesCAT5 CABLE Connect a Cat5 cable to the RJ-45 network connector. The 8-pin connector includes video and PoE for the cam

12 C2941M-C (6/08)The following are the recommended maximum distances for 24 VAC applications and are calculated with a 10-percent voltage drop. (Ten

C2941M-C (6/08) 13Lens Setup and Focus ProceduresVIDEO DRIVE AUTO IRIS LENS1. Set the lens mode selector switch to AIV. 2. Switch the electronic shut

14 C2941M-C (6/08)MANUAL IRIS LENS1. Set the ESC and AGC switches to ON (default settings).2. Focus the lens.a. Open the iris fully and set the lens

C2941M-C (6/08) 15Back Focus AdjustmentThe back focus adjustment is located at the front of the camera and is accessible from either side of the case

16 C2941M-C (6/08)Switch SettingsFigure 8. DIP Switch Default SettingsNOTES:• White indicates the switch setting.• Under most conditions, you will no

C2941M-C (6/08) 17tNot UseduExtended dynamic range (EDR)OFF (default setting): Disables the EDR mode.EDR: Enables the EDR mode to help balance a scen

18 C2941M-C (6/08)Dynamic Range and EDR Dynamic range is the ratio between the brightest and darkest parts of an image or scene. A scene that ranges

C2941M-C (6/08) 19TroubleshootingProblem Possible Cause Suggested RemedyNo video PoE power issue • Verify Cat5 cable connection.• Verify PoE is enabl

20 C2941M-C (6/08)Image too light Installation error • Verify DIP switch settings.• Use a service connector to verify camera operation. Connect one e

C2941M-C (6/08) 21SpecificationsGENERALConstructionFinish Black polyester powder coatImaging Device 1/3-inch imagerPicture ElementsIP3701H-2 768 (H)

22 C2941M-C (6/08)ENVIRONMENTALOperating Temperature 14° to 122°F (-10° to 50°C)Storage Temperature 14° to 158°F (-10° to 70°C)PHYSICALDimensions 4.5

PRODUCT WARRANTY AND RETURN INFORMATIONWARRANTYPelco will repair or replace, without charge, any merchandise proved defective in material or workmansh

Worldwide Headquarters3500 Pelco WayClovis, California 93612 USAUSA & CanadaTel: (800) 289-9100Fax: (800) 289-9150InternationalTel: +1 (559) 292-1

C2941M-C (6/08) 3ContentsImportant Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4 C2941M-C (6/08)Important Safety Instructions1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instruction

C2941M-C (6/08) 5Regulatory NoticesThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this

6 C2941M-C (6/08)DescriptionThe IP3701H-2 Series is a high resolution, color video camera with a built-in 100Base-TX network interface for live strea

C2941M-C (6/08) 7Basic System ConfigurationsIMPORTANT NOTE. PLEASE READ. The network implementations in this document are shown as general representa

8 C2941M-C (6/08)Figure 3. Private Network ExampleFigure 4. Static Network ExampleIF NOT DHCP, CAMERA IS ASSIGNEDDEFAULT IP ADDRESS 192.168.0.20 ON

C2941M-C (6/08) 9Camera LayoutFigure 5. Camera LayoutRESET BUTTONUse the reset button located on the side of the camera to access the following modes