Pelco C2941M Bedienungsanleitung

INSTALLATIONC2941M (8/07) IP3701H-2 and IP3701H-2X IP Color Camera

10 C2941M (8/07) Installation LENS MOUNTING The camera can use a fixed iris, manual iris or auto iris lens. The camera is factory set for a CS-mount l

C2941M (8/07) 11 Wiring Tables CAT5 CABLE Connect a Cat5 cable to the RJ-45 network connector. The 8-pin connector includes video and PoE for the ca

12 C2941M (8/07) Table C. Recommended Wire Gauge and Wiring Distances The following are the recommended maximum distances for 24 VAC applications a

C2941M (8/07) 13 Lens Setup and Focus Procedures VIDEO DRIVE AUTO IRIS LENS Set the lens mode selector switch to AIV. Switch the ESC and AGC OFF. Ref

14 C2941M (8/07) Back Focus Adjustment The back focus adjustment is located at the front of the camera and is accessible from either side of the case

C2941M (8/07) 15 Switch Settings Figure 8. DIP Switch Default Settings NOTE: Under most conditions, no setting of switches will be required. Plea

16 C2941M (8/07)  Not Used  EDR: Extended dynamic range• Off (Default setting): Disables the EDR mode.• EDR: Enables the EDR mode to help balanc

C2941M (8/07) 17 Dynamic Range and EDR Dynamic range is the ratio between the brightest and darkest parts of an image or scene. A scene that ranges

18 C2941M (8/07) Troubleshooting Problem Possible Cause Suggested Remedy No video PoE power issue • Verify Cat5 cable connection.• Verify PoE is ena

C2941M (8/07) 19 Image too light • Verify DIP switch settings.• Use a service connector to verify camera operation. Connect one end of the service co

20 C2941M (8/07) Specifications GENERAL ConstructionFinish Black polyester powder coatImaging Device 1/3-inch imagerPicture ElementsIP3701H-2 768 (H)

C2941M (8/07) 21 Minimum Web BrowserRequirements PC (Pentium ® 4 microprocessor, 1.6 GHz) with Windows ® 98, Windows 2000, Windows XP (or higher),

22 C2941M (8/07) The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/E

PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workma

Worldwide Headquarters3500 Pelco WayClovis, California 93612 USAUSA & CanadaTel: 800/289-9100Fax: 800/289-9150InternationalTel: 1-559/292-1981Fax:

C2941M (8/07) 3 Contents Important Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4 C2941M (8/07) Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instruction

C2941M (8/07) 5 Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this

6 C2941M (8/07) Description The IP3701H-2 and IP3701H-2X are high resolution, color video cameras with a built-in 100Base-TX network interface for li

C2941M (8/07) 7 Basic System Configurations IMPORTANT NOTE. PLEASE READ. The network implementations in this document are shown as general representa

8 C2941M (8/07) Figure 3. Private Network Example Figure 4. Static Network ExampleIF NOT DHCP, CAMERA CYCLESTHROUGH IP ADDRESS RANGE169.254.200.0

C2941M (8/07) 9 Camera Layout Figure 5. Camera Layout RESET BUTTON Use the reset button located on the side of the camera to access the following m