Pelco C2622M Bedienungsanleitung

®INSTALLATIONFX82051 UnmanagedEthernet SwitchFive 10BASE-T/100BASE-TX Ports and One 100BASE-FX Fiber PortC2622M (2/07)

10 C2622M (2/07)InstallationPACKAGE CONTENTSThe following items are supplied:1 FX82051 module1 Regulated switching power supply with four plug adapter

C2622M (2/07) 11Using the TX Mode switch for a particular port, you can do the following:• Enable autonegotiation or select (force) a specific data ra

12 C2622M (2/07)Table A. TX Mode Switch SettingsTX Mode Switch Position 10BASE-T/100BASE-TX Modes of Operation0 Auto Neg/Dis FC: Enables autonegotiat

C2622M (2/07) 13MOUNTINGThe FX82051 module can be mounted into a rack or can be used as a stand-alone module. As a stand-alone module, the unit can be

14 C2622M (2/07)Mounting the FX82051 Module Using the Wall ClipNOTE: Before mounting the FX82051 module to a wall, ensure that there is adequate space

C2622M (2/07) 15CONNECTIONSConnections to the FX82051 module are made on the rear panel of the module (refer to Figure 6). Figure 6. FX82051 Module C

16 C2622M (2/07)Figure 7. Fiber Port Connections in Point-to-Point Application

C2622M (2/07) 17TroubleshootingLED indicators on the front and rear panels of the FX82051 module allow you to monitor operational status:• LED indicat

18 C2622M (2/07)Optic Fault LED ( )Green The optical signal is being received and laser is operating properly.— No action required.Red The optical sig

C2622M (2/07) 19Table C. Troubleshooting with Rear-Panel IndicatorsIndicator Color Meaning Possible Cause Corrective ActionRJ-45 10BASE-T/100BASE-TX

2 C2622M (2/07)ContentsImportant Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20 C2622M (2/07)RJ-45 10BASE-T/100BASE-TX Port Status LED - Left (Link/Activity) (Continued)Not lit A 10BASE-T or 100BASE-TX link cannot be establishe

C2622M (2/07) 21RJ-45 10BASE-T/100BASE-TX Port Status LED - Right (Duplex/Collision)Amber Port is set to 10BASE-T full-duplex mode.— If 10BASE-T full-

22 C2622M (2/07)RJ-45 10BASE-T/100BASE-TX Port Status LED - Right (Duplex/Collision) (Continued)Green Port is set to 100BASE-TX full-duplex mode.— If

C2622M (2/07) 23RJ-45 10BASE-T/100BASE-TX Port Status LED - Right (Duplex/Collision) (Continued)Not lit Port is set to 10BASE-T half-duplex mode and n

24 C2622M (2/07)SpecificationsPERFORMANCESwitch Type Unmanaged Layer 2Switch Method Store and forwardSwitch Fabric Non-head-of-line blockingData Rate

C2622M (2/07) 25OPTICAL POWER BUDGET, TRANSMISSION DISTANCE, AND LASER CLASS 1 LIMITModel NumberWavelength(Transmit/Receive)Optical Power BudgetMaximu

26 C2622M (2/07)Appendix. RJ-45 Connector Pinouts Figure 8 illustrates RJ-45 MDI/MDI-X connector pinouts.Figure 8. RJ-45 MDI/MDI-X Connector PinoutsT

PRODUCT WARRANTY AND RETURN INFORMATIONWARRANTYPelco will repair or replace, without charge, any merchandise proved defective in material or workmansh

®Worldwide Headquarters3500 Pelco WayClovis, California 93612 USAUSA & CanadaTel: 800/289-9100Fax: 800/289-9150InternationalTel: 1-559/292-1981Fax

C2622M (2/07) 3Important Safety Instructions1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.5. D

4 C2622M (2/07)The product and/or manual may bear the following marks:This symbol indicates that dangerous voltage constituting a risk of electric sho

C2622M (2/07) 5Regulatory NoticesThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this de

6 C2622M (2/07)Product OverviewDESCRIPTIONThe FX82051 unmanaged Ethernet switch provides five 10BASE-T/100BASE-TX ports and one 100BASE-FX fiber port

C2622M (2/07) 7• Designed to meet NEMA TS 2 and Caltrans traffic signal control equipment standards for ambient operating temperature, mechanical shoc

8 C2622M (2/07)FRONT PANELFigure 2 illustrates the front panel of the FX82051 module. Figure 2. Front Panel of FX82051 ModuleFor detailed information

C2622M (2/07) 9REAR PANELFigure 3 illustrates the rear panel of the FX82051 module. Figure 3. Rear Panel of FX82051 Module (SC Fiber Connector Shown)