Pelco pelco dx8000 Bedienungsanleitung

DX8000 Hard DriveUpgrade Installationto a Two-Drive SystemsC1607M (6/04)Digital Video RecorderDX8000

8 C1607M (6/04)Move the Front Cross-Brace1. Unscrew and lift out the front cross-brace (found at the center of the unit). Moving this part out of the

C1607M (6/04) 9b. Carefully place the cross-brace and fan across the rear section of the unit. Refer to Figure 7.WARNING: Do not disconnect the wires

10 C1607M (6/04)Disconnect the Data Cable and Power WireWhen removing the data cable and power wires, pull the connectors straight out. Do not rock co

C1607M (6/04) 112. Remove the power connector from the hard drive.2HARD DRIVEPOWER CONNECTORFigure 9. Removing Hard Drive Power Connection

12 C1607M (6/04)Remove the Drive Mount Baskets1. Remove hard drive mounting basket:a. Using a Phillips-head screwdriver, unfasten and save the four sc

C1607M (6/04) 13Install an Additional DriveNOTE: This upgrade kit includes a Pelco-certified hard disk drive to be installed as an additional unit. Us

14 C1607M (6/04)MOUNT THE ADDITIONAL DRIVE1. Mount Hard Disk 2 adjacent to Hard Disk 1 in the drive basket closest to the CD-RW drive. Refer to Figure

C1607M (6/04) 152. Mount the drive basket back into the chassis:a. Align the basket and press down firmly to ensure that it fits flush against the top

16 C1607M (6/04)SET THE MASTER / SLAVE JUMPERSEach hard drive must be configured as either a master or slave device to operate correctly. A jumper is

C1607M (6/04) 17DRIVE 2 SLAVEDRIVE 1 MASTERCD-RWFRONT OF DVRJUMPERSLAVESETTINGMASTERSETTINGFigure 15. Setting Drive Jumpers

Protecting people and property in a million locations worldwide.

18 C1607M (6/04)RECONNECT THE DATA AND POWER CABLESIMPORTANT: Data and power connectors fit together only one way. All connectors are keyed to ensuret

C1607M (6/04) 192. Using the straight data cable that came with your upgrade kit, connect Hard Drive 1 and Hard Drive 2 to the systemmotherboard:a. Co

20 C1607M (6/04)3. Connect the hard drive power connectors according to the diagram in Figure 18.Figure 18. Installing Hard Drive Power Connectors3

C1607M (6/04) 21Reassemble the Unit1. Replace the front cross-brace and secure it with the flat-head screws you set aside earlier. Refer to Figure 19.

22 C1607M (6/04)2. Replace the chassis cover using the same screws you removed from the side and rear of the unit. Refer to Figure 20.Figure 20. Repla

C1607M (6/04) 233. Reinstall the unit in a rack enclosure if necessary, and reconnect all cables and peripheral equipment that youremoved earlier.4. P

24 C1607M (6/04)Preparing the New Drives to Store Data1. While the DX8000 starts, the built-in setup program will automatically detect the newly insta

C1607M (6/04) 25b. For each drive listed, click the Not Used button. Refer to Figure 23. A drop-down menu appears. There may bemore than one drive lis

26 C1607M (6/04)d. Click Begin Allocation.Figure 25. Initializing Drive Allocatione. The following warning appears. Click Yes.Figure 26. Format Warnin

C1607M (6/04) 27f. Wait while the DX8000 prepares the newly installed drives for video storage. You will see the followingprogress bar while the forma

C1607M (6/04) 1IntroductionThe following instructions serve as a guide for upgrading the storage capacity of the DX8000 series digital video recorder(

28 C1607M (6/04)Notes

PRODUCT WARRANTY AND RETURN INFORMATIONPRODUCT WARRANTY AND RETURN INFORMATIONWARRANTYPelco will repair or replace, without charge, any merchandise pr

Pelco and the Pelco logo are registered trademarks of Pelco. © Copyright 2004, Pelco. All rights reserved.Windows is a registered trademark of Microso

2 C1607M (6/04)Getting Ready1. Familiarize yourself with the instructions throughout this manual.2. Check that you have all the necessary parts and to

C1607M (6/04) 3Figure 2. Removing Power Cord from Unit

4 C1607M (6/04)Figure 3. ESD Protection5. Ensure that the DX8000 Series DVR and all of its components are protected against electrostatic discharge (E

C1607M (6/04) 5Preparing Unit for Drive InstallationIMPORTANT: If this upgrade requires the replacement of the DX8000’s primary hard disk drive (drive

6 C1607M (6/04)3. Using a Phillips-head screwdriver, remove the chassis cover:WARNING: Make sure unit is turned off and you are wearing a properly gro

C1607M (6/04) 7COMPONENT LAYOUTFigure 5 shows the location of your DX8000 Series DVR’s major components. Certain cables and components have beenomitte