Pelco PT7700 Bedienungsanleitung

C997M3500 Pelco Way, Clovis, CA 93612-5699 • (559) 292-1981 • (800) 289-9100• FAX (800) 289-9150WARNING!®Warning! When lifting, transporting, or un-pa

Pelco Manual C397M (4/98) 9PT7729RXPT7723RX-1PT7729RX-1PT7729RX-3PT7729RX-1/SLBase ConnectorPin AssignmentsPT7729WXPT7723WX-1PT7729WX-1PT7729WX-3Base

10 Pelco Manual C397M (4/98)3.4 TESTING SYSTEM AND ADJUSTING LIMIT STOPSTo test the system and adjust the limit stops:1. Loosen the two pan limit sto

Pelco Manual C397M (4/98) 114.0 OPERATIONRefer to the manual for your control equipment for operating the pan/tilt system.If your enclosure has a the

12 Pelco Manual C397M (4/98)5.0 TROUBLESHOOTINGFuses are located inside the left cover of the pan/tilt unit. Fuses F1 (mother board)and F2 (camera) a

Pelco Manual C397M (4/98) 136.0 MAINTENANCEPerform the following maintenance at six-month (or more often in harsh environ-ments) intervals to prolong

14 Pelco Manual C397M (4/98)Tilt Adjustments and Lubrication10. Remove the plastic cover on the right side of the pan/tilt unit.11. Refer to Figure 5.

Pelco Manual C397M (4/98) 157.0 EXPLODED ASSEMBLY DIAGRAMSFigure 6. Exploded Assembly Diagram for Blower and Circuit BoardSCREWS COME WITHBLANKING P

16 Pelco Manual C397M (4/98)Table A. Parts List (Figure 6)Item Qty Description Part Number1 1 Vent Grill 57004005COMP2 2 Foam Filter EH5500100454 1 C

Pelco Manual C397M (4/98) 17Figure 7. Exploded Assembly Diagram for Heaters and Circuit BoardTable B. Parts List (Figure 7)Item Qty Description Part

18 Pelco Manual C397M (4/98)Figure 8. Wiring Diagram for Enclosure Circuit Board

Pelco Manual C397M (4/98) 1®Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 • USA • www.pelco.comIn North America and Canada: Tel (800) 289-9100 • FAX

Pelco Manual C397M (4/98) 19Figure 9. Component Locations for Enclosure Circuit BoardFigure 10. Layout of Traces on Enclosure Circuit Board

20 Pelco Manual C397M (4/98)8.0 SPECIFICATIONSSYSTEMInput Voltage: 120 or 230 VAC, 50/60 HzPower Requirements:PT7729RX,PT7729WX 0.35 A (42 vA)PT7729R

Pelco Manual C397M (4/98) 21PAN/TILTConstructionBody: Aluminum plateSide Covers: Vacuum-formed ABS plastic, UV protectedPan: 0-355° movement in horizo

22 Pelco Manual C397M (4/98)Wiretron Receiver/DriverFuses: One 1 A, 3 AG typeTwo 2/10 A, 3 AG typeControl Method: 15 pulse train (pulse width modulate

Pelco Manual C397M (4/98) 23Figure 11. Dimension DrawingMODEL “A” “B”PT7729RX 32.50 (82.55) 29.00 (73.66)PT7729RX-1PT7729RX-1/SLPT7729RX-1/PPPT7729RX

24 Pelco Manual C397M (4/98)9.0 WARRANTY AND RETURN INFORMATIONPelco, the Pelco logo, Camclosure, Esprit,Genex, Legacy, and Spectra are registeredtra

2 Pelco Manual C397M (4/98)LIST OF ILLUSTRATIONSFigure Page 1 PT7700 Series Input Wiring Diagram ... 8 2

Pelco Manual C397M (4/98) 3Please thoroughly familiarize yourself with the informationin this manual prior to installation and operation.1.0 GENERAL1

4 Pelco Manual C397M (4/98)2.0 DESCRIPTIONThe PT7700 systems combine an environmental camera enclosure, pan/tilt as-sembly, and receiver/driver into

Pelco Manual C397M (4/98) 53.0 INSTALLATION3.1 MOUNTINGAttach the base of the pan/tilt system to a flat surface. If you use a wall or pedestalmount,

6 Pelco Manual C397M (4/98)j. On the bottom of the enclosure, remove the vent grill and filters at thefront of the enclosure. Replace the grill with o

Pelco Manual C397M (4/98) 73.3 WIRING1. Route the six-foot power/video/control cable through the wall or pedestal mountif applicable.2. Connect the e

8 Pelco Manual C397M (4/98)Figure 1. PT7700 Series Input Wiring Diagram